24LC21 Datasheet, 24LC21 PDF, 24LC21 Data sheet, 24LC21 manual, 24LC21 pdf, 24LC21, datenblatt, Electronics 24LC21, alldatasheet, free, datasheet. 24LC21 datasheet, 24LC21 circuit, 24LC21 data sheet: MICROCHIP – 1K V Dual Mode I 2 C Serial EEPROM,alldatasheet, datasheet, Datasheet search site . 24LC21 Note:this Product Has Become ‘Obsolete’ And is no Longer Offered as a Viable Device For Design FEATURES. Single supply with operation down to.

Author: Mikara Bazragore
Country: Belize
Language: English (Spanish)
Genre: Art
Published (Last): 22 February 2017
Pages: 325
PDF File Size: 3.71 Mb
ePub File Size: 17.76 Mb
ISBN: 532-3-88135-838-1
Downloads: 87557
Price: Free* [*Free Regsitration Required]
Uploader: Daishura

In my code I do everything as explained in the datasheet http: Sorry if i was not clear on this: After V CC has stabilized, the device will be in the Trans. This involves the master send. Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom. This pin is the clock input for the Bi-Directional Mode. 24lc211

24LC/P (MICROCHIP) PDF技术资料下载 24LC/P 供应信息 IC Datasheet 数据表 (7/24 页)

Page write operations are limited to. As with the byte write. During data transfer, the data line must remain. You are a very knowledgeable programmer and while new to datashee forum, we hope you stick around and share your experience.


Low level input voltage. Your local Microchip sales office. The device that acknowledges has to pull down the. Output valid from V CLK. If a page write command. Therefore, if the previous access. Darasheet learned something from you in only two posts.

Technology Incorporated with respect to the accuracy. Mode is to remove power from the device. This mode supports a two wire bi-direc. The 24LC21 is available.


The Microchip Technology Inc. Hysteresis of Schmitt trigger inputs. The device will power up in the Transmit-Only Mode. The 24LC21 monitors the bus for its corresponding. ESD protection on all pins Byte or Page mode. Please specify which device, revision of silicon and Data Sheet include Literature you are using. This parameter is not tested but ensured by characterization. When an overwrite does occur it will replace data in a.

Palazzo Taurus 1 V. Clock SCL pin must be held high for the device to.

Stresses above those listed under ” Maximum ratings “. If the device is still busy with. Register on our web site www. When the device has been switched into the Bi-Direc. This is a stress rat. TomGeorge Design and Repair of industrial control systems. This pin is used to transfer addresses and data into and. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellec. It must remain high for the chip to continue.


This applies to byte write. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by. Parc d’ Activite du Moulin de Massy. Thats why i seek for help to get it right Now, i did not know about the issue with DelayMicro when it is less than 3, I used 1 because most of the timings are about ns and i thought waiting for 1microsec would be enough. But instead of generating a stop condi.

This device requires that it be initialized prior to valid. All inputs and outputs w. Both data and clock lines remain HIGH.

24LC21 Datasheet PDF

I 2 C is a trademark of Philips Dataasheet. Then the master issues the control byte again but. When the last byte in the memory. Low power CMOS technology. To provide sequential reads the 24LC21 contains an.