DIN 5480-1 PDF

Buy DIN INVOLUTE SPLINES BASED ON REFERENCE DIAMETERS – PART 1: GENERALITIES from SAI Global. March DIN Splined connections with involute splines based on reference diameters — Part 1: Principles Passverzahnungen mit Evolventenflanken. March DIN Splined connections with involute splines based on reference diameters — Part 1: Principles Passverzahnungen mit.

Author: Dourn Dozil
Country: Albania
Language: English (Spanish)
Genre: Politics
Published (Last): 15 April 2006
Pages: 250
PDF File Size: 16.72 Mb
ePub File Size: 9.91 Mb
ISBN: 991-4-25998-438-8
Downloads: 43976
Price: Free* [*Free Regsitration Required]
Uploader: Malasar

DIN Splined connections with involute splines based Following are the tables with the available hobs and cutters.

Internal and external spline teeth

Create your own flipbook. The designations given inDIN for gear teeth are also permitted. There are six deviations, from F to M for hubs and 18 deviations from v to a for shafts.

The statistical actual tolerance limit permits a certain number of measurements to exceed the tolerance limits by a specific value. In practice, the size of the actual tolerance Tact in relationship to the effective tolerance Teff within the overall tolerance TG varies very strongly.

DIN Validity This standard is valid from onwards. Involute splines in accordance with ISO are based on series of modules.

Eight tolerance classes are available for the magnitude of the overall tolerances of hubs and shafts. DIN Table 5: Preferred series, reference diameters dB from 60 mm to mm Calculation of tolerance limits Given these values, it is the designer’s task to select the deviations and tolerance classes. In the case of numbers of teeth which 55480-1 not prime numbers, the centring surfaces can be widened bymultiple teeth on the shaft and multiple spaces in the hub, for instance in order to make diameter-centredconnections stronger or to allow diameter centring with small modules see figure 55480-1.

The object of the revision was to combine the individual parts of this standard in a practical, useful and sensible manner. A number of teeth expressed as 6 12 indicates six double teeth out of a total of DIN defines the design features of tools for manufacturing items with involute splines.


It is 548-1 to state standard values for this. The corresponding descriptive parameters, tooth interlock data andcalculation formulae are given in table 3. DIN Figure 1: These are not interchangeable with involute splines as described by the DIN series of standards.

The intention which is the basis of this idea is: However, dih thiscase a note must be added stating that the GO gauge has priority.

DIN 5480-1 Splined connections with involute splines based …

Since it is difficult to measure tooth thickness and space widths directly, they are converted to dimensions across and between measuring circles and are entered in this form into the data field. As analternative, this can also be done using the deviation factors as described in DIN DIN Table 6: The calculation formulae, tolerances and deviations contained in Part 1 also apply to the other parts of this series of standards.

In shafts, the superposition of all individual deviations lead to an effective tooth thickness that is greater than the actual thickness which can be measured. These should therefore only be used in a few exceptional cases.

DIN covers quality inspections of fitted splined connections. For a minimum fit clearance of zero, it isbetter to set the effective tolerance limits to the dimension of the nominal space width e2 and the nominal tooththickness s1. Refer to clause 10 for the relationship between space width tolerance and tooth thickness tolerance, measurement methods, 54800-1 mesh quality and backlash.

The DIN series of standards is based on reference diameters that are independent of the module. The nominal dimensions of the centring diameters of diameter-centred connections are the referencediameters for external diameter centring or of the hub tip circle diameters for internal diameter centring. The difference between the space width and the tooth thicknessdetermines the rotational backlash.


These lead to negative signs for all hub diametersand dimensions see DIN DIN for all calculations in respect of fitted splined connections. For diameter-centring, the tolerance class andthe deviation series are placed in front of the respective data of the tooth flanks. The symbol z then represents thenew odd number of spaces. For choosing the number of keys depending on the diameters and of the load, as also for indicating the tolerances according to the desired fit loose, sliding, straining we refer to the tables published by the various standardization organizations:.

Profile of the shaft The form of the slots as indicated above is closely linked to the finish method. The reasons for this are explained insubclause 7. Preferred series, reference diameters dB from 6 mm to 58 mm Figure1 shows an externally-centred shaft with splines.

DIN Splined connections with involute splines based

Profile of the nave B: DIN now contains the nominal dimensions and inspection dimensions for the range of items stated above. Compliance with the effective tolerance limit is checked usingfully-splined GO gauges.

For details, see DIN5. See table 5 for recommended tolerance fields of the root circle and tip circle diameters. The property defining the fit is the fit of the flanks, the backlash. The fit and the centring accuracy are determined by the deviations of the space widths and thicknesses as well as by the tolerances achieved or specified.