BS EN 61439-1 PDF

date BS EN is withdrawn and BS EN and BS EN In addition IEC and IEC have been amended, clarified and. For each type of electrical AssEMBLY only two parts of the standard are necessary to determine all requirements: the basic standard IEC “ General rules. What changes does BS EN bring? • New testing procedure including design and routine verification. • Alternative testing routes. • Clear requirements for.

Author: Meztinris Maull
Country: Kenya
Language: English (Spanish)
Genre: Life
Published (Last): 14 March 2009
Pages: 18
PDF File Size: 19.31 Mb
ePub File Size: 8.93 Mb
ISBN: 788-6-98071-310-2
Downloads: 90960
Price: Free* [*Free Regsitration Required]
Uploader: Samutaxe

Data associated with loads likely to contribute 614391- the 9. Where the device manufacturer specifies a conductor with a larger cross sectional area this shall be used; g the temperature rise depending on the power loss installed in the enclosure, with or without forced cooling, and for the allowed different installation methods e.

Electrical testing, Marking, Instructions for use, Voltage measurement, Verification, Electric control 61493-1, Approval testing, Rated frequencies, Access, Circuits, Performance testing, Electric shocks, Installation, Name plates, Low-voltage equipment, Dielectric properties, Testing conditions, Electrical properties of materials, Electric terminals, Electromagnetic compatibility, Type testing, Clearances, Classification systems, Environment workingElectronic equipment and components, Electrical equipment, Electrical connections, Temperature rise, Impulse-voltage tests, Inspection, Electrical insulation, Switchgear, Electrical protection equipment, Leakage paths, Electrical safety, Electric conductors, Temperature measurement, Dielectric-strength tests, Rated current, Rated voltage.

NOTE 2 The term “sparkover” is used when a disruptive discharge occurs in a gaseous or liquid dielectric. You may experience issues viewing this site in Internet Explorer 9, 10 or Power switchgear and controlgear assemblies 1 Scope This clause of Part 1 is applicable except as follows.

Where basic protection is achieved by constructional measures one or more of the protective measures given in 8. Where an obstacle or shutter is used they shall meet the requirements of 8. The test shall be made for a time sufficient for the temperature rise to reach a constant value.

The test specimens shall be new and fn a clean condition and shall be subjected to severity test A or B, as detailed in Openings in cable entries, cover plates, etc. For voltages which are within the tolerance band stated in IECthe disconnecting time appropriate to the nominal voltage applies.

Cooling air available to a circuit may be at a temperature well in excess of the ambient due to the influence of other circuits. During the test, with the test weights in place, the ASSEMBLY shall show no deflections and after the test show no cracks or permanent distortions visible to normal or corrected vision without additional magnification, which could impair any of its characteristics.

To avoid the risk of 614339-1 fault to earth, particular attention shall be given to the insulation of such parts from earth, especially for flexible cables and cords.

  AMBA AXI4 SPECIFICATION PDF

BS EN 低压开关设备和控制设备装配模块.电源开关设备和控制设备装配模块 – MBA智库文档

For the test carried out in accordance with ISO no grooves shall be cut into the sample and the impact shall be applied to the exposed surface. In general, removal and installation of fixed parts requires the use of a tool.

Tests — Test Ka: The switching eb shall be closed and held closed in the manner normally used in service.

All parts of the equipment intended to be connected to the protective conductor in service, including the enclosure, shall be connected as follows: Ingress of water is permissible only if its route of entry is obvious and the water is only in contact with the enclosure at a location where it will not impair safety.

The assumed load current for each circuit is 8 A. Type-tested and partially type-tested assemblies AMD For protection, by total insulation, against indirect contact the following requirements shall be met. In locations where heavy vibrations exist during normal operation, for example in the case of dredger and crane operation, operation on board ships, lifting equipment and locomotives, attention should be given to the support of conductors. Protection for safety – Protection against voltage disturbances and electromagnetic disturbances IEC Electrical installations of buildings – – – Part If the direction of operation is not in accordance with IECthen the direction of operation shall be clearly identified.

It is the constant aim of BSI to improve the quality of our products and serv-Tel: Provides definitions and service conditions for assemblies with rated voltage not exceeding 1,V a. For this additional test, the test voltage shall be equal to 1,5 times the values indicated in Table 8.

To ensure that our lifting methods and procedures are compliant we have conducted independent tests on sample products covering the areas listed in this clause. Openings larger than those defined by degree of protection IP XXC are allowed during b replacement of certain lamps or fuselinks.

British Standards

However, mounting rails made of copper or aluminium may be used as PEN conductors; — for certain applications in which the current in the PEN conductor may reach high values, for example large fluorescent lighting installations, a PEN conductor having the same or higher current-carrying capacity as the phase conductors may be necessary, subject to special agreement between the ASSEMBLY manufacturer and the user. NOTE 614399-1 working on live circuits is permitted, relevant safety precautions may be necessary.

Equipment utilizing electronic circuits 661439-1 which all components are passive for example diodes, resistors, varistors, capacitors, surge suppressors, inductors are not required to be tested. NOTE 2 The maximum load b are used for the calculation instead of the rated currents of the circuits and the rated diversity factor because these two rated values need more detailed consideration of different load conditions.

  INVENTARIO BECK DEPRESION PDF

For this test the incoming circuit is loaded to its rated current and each outgoing functional unit to its rated current multiplied by the rated diversity factor.

It shall be connected to the main bw the distribution busbar as in normal use. This symbol is not required where the external protective conductor is intended to be connected to an internal protective conductor, which is clearly identified with the sb green and yellow. NOTE 2 For conductors 16439-1 than copper conductors, the above cross-sections should be replaced by cross-sections of equivalent conductivity, which may require larger terminals. They shall be mounted in the enclosure as in normal use with all covers and all partitions that separate the busbar from other compartments, in place.

The power losses of the conductors are determined by calculation see Annex H. However surface deterioration of the protective coating is allowed. The effective power losses of all circuits including interconnecting conductors shall be calculated based on maximum load currents of the circuits. The test shall be conducted at 1,05 times the rated operational voltage with prospective short circuit currents, at the supply side of the specified protective device, equal to the value 614391 the rated conditional short-circuit current.

This current shall be carried without the temperature rise of the individual parts exceeding the limits specified in 9. Selection and erection of electrical equipment – Wiring systems IEC Electrical installations of buildings – – – Part Unless otherwise agreed between the ASSEMBLY manufacturer and the user, on three-phase and neutral circuits, terminals for the neutral conductor shall allow the connection of copper conductors having a current-carrying capacity: Paints, varnishes and lacquers fn are not considered to satisfy the requirements for basic insulation.

Introduction to 61439-1

Small capacitors such as those used for arc extinction, for delaying the response of relays, etc. Phase to neutral short-circuit connections shall be applied as specified in These product parts call up the ej EMC requirements of EN for assemblies within their specific scope. The specimen is considered to have withstood the glow-wire test if — 61439-11 is no visible flame and no sustained glowing, or if — flames and glowing of the specimen extinguish within 30 s after removal of the glow-wire.

Tests are required at 1. Low-voltage switchgear and controlgear assemblies IEC